The New Voopoo Drag M100s Sub Ohm Kit with the new Uforce L tank which utilises the extremely reliable Pnp Coils.

Utilising the New Generation GENE.TT 2.0 Chip the battery can run from 5-100w Powered by 1 x 21700 Battery or 1 x 18650 Battery (sold separately)

The new tank has threeway top airflow and filling which is leakproof and has a heatsink to disperse the extra heat created by the excellent mesh coils. With the range of coils available this truly is a versatile vape which can be used as MTL (Mouth to Lung) RDL (Restricted direct to lung) of full DTL (Direct to lung) with the excellent range of PnP coils available.

Replacement Uforce L Tank Glass and Uforce L XL Tank for the M100s Kit are also available

Features:

• Name: Drag M100s
• Material: Zinc Alloy + Wood/AG Matte Finish
• Output Power: 5-100W
• Output Voltage: 0-8.5V
• Resistance: 0.05~3.0ohm
• Battery Capacity: Single 21700 battery or 18650 battery (sold separately)
• Compatible Coils: All of PNP Coils
• Size: 36mm x 30mm x 90mm
• New Generation GENE.TT 2.0 Chip

Contents:

• 1×DRAG M100s Device
• 1×Uforce L Tank
• 1×PnP TW20 0.2 ohm coil
• 1×PnP TW15 0.15 ohm coil
• 1×User Manual
• 1×Type-C Cable

*A copy of the Drag M100s Kit manual is available to view on this page in the manual tab

Notes on Priming Coils

• Always prime your coils well when using for the first time
• Add 5 or so drops to the centre of the coil saturating the cotton
• Reassemble the tank making sure the coil is secured in place
• Add your chosen liquid to the tank
• Take 5 or so long drags on your device without power
• To be absolutely sure leave rested upright for a minute or so

For devices that use external cells.

It is not recommended that users charge their separate cell devices with a usb lead in to the device. These devices can be charged via usb as an emergency measure but is not recommended as a permanent solution. This is not a line to sell chargers there are significant reason why it should be done externally. Do not assume that it is safe. These batteries are not made for vaping and the manufacturer has no idea what cells you are using. Best to use the safer solution of a named quality charger.

1. Most vapes cannot balance charge more than one cell. One cell is charged and then after that the next cell is charged. All of the drain, excess heat and over use of that one cell causes strain on that 1st battery in the vape and ultimately leads to the demise of that 1 battery leading to the need of a new pair. If lucky it will just stop working if unlucky the cell may go into melt down
2. If your batteries are not the same age, ie the same amount of charges, the same amount of use and charged together for their whole lives then they are unbalanced. Meaning they cannot deliver the high output required by your vape. This will lead to low performance and low battery life.
3. External chargers let you monitor the charge going in to your cells. Good quality chargers will put what is needed in as opposed to as much as possible as fast as possible which can caused issues. A good charger will slow the charge rate down to recondition a bad cell. Internal charging will not do this. Using a good external charger could mean your batteries getting you through a day away from your charging equipment or not. Ultimately it is up to you how safe you want to be. Yes an external charger may sound like a hassle to you but it depends on the risks you want to take.

Please make sure your external cells have perfectly intact wraps on them If they have any of the metal showing under the wrap or the insulator on top please either re wrap or buy new cells PS This is not to scare you If you have any doubts about your charging routine just ask. Batteries get warm when they charge but if they are red hot then its time to look into it

• Voopoo Drag M100s User Manual